• Know Your Speaker System. Generally in systems all the cables from the speakers are connected to the subwoofer which comes with a set of wires to connect, that includes: a power cord to connect the system to the AC outlet, a power connector to feed the subwoofer and the subwoofer wires.
• Jump to Connecting Wired Computer Speakers - Connecting Wired Computer Speakers. Windows users will probably see two different sliders—use the.

I bought a set of loudspeakers for my pc, (logitech z .200) and an audio interface for my microphone. The loudspeakers are wired jointly and I had been wondering if it had been probable to cut the cables connecting the audio speakers and put RCA plugs on them tó connect them intó the back again of my audio interface. The left speaker just offers the wire hooking up it to the right speaker, and the correct speaker provides the connecting cable, energy, and a 3.5mmeters for hooking up it to the computer.Will be this in any way probable? And if therefore, what precisely would I need to perform?Thanks. I purchased a collection of audio speakers for my computer, (logitech z .200) and an audio interface for my microphone. The audio speakers are usually wired jointly and I was curious if it was feasible to reduce the cables hooking up the loudspeakers and place RCA attaches on them tó connect them intó the back of my audio user interface.

1) You want to hook up speaker cables to speaker outputs. In this case, usually people use speaker wire, because one side is labeled in some fashion. You hook up the labeled side to the black speaker jacks and the other to red ( or the reverse, but you have to be consistent.) 2) You have some system which has speaker outputs with RCA jacks.

The remaining speaker only has the cable linking it to the correct speaker, and the right speaker has the connecting cable, strength, and a 3.5mmichael for connecting it to the personal computer.Is certainly this in any way probable? And if therefore, what exactly would I need to perform?ThanksNot actually. The left speaker wants to get power from the right speaker.As over, just obtain a 3.5mm-RCA adapter.

A series out or héadphone out expects usually a ohmic resistance of 60 or even more and delivers low voltage/current, that will be called pre-amplifier level. A speaker generally has a 4 to 8 ohm resistance, wich could appear to your sóundcard like a short circuit, forcing it to deliver higher current and ultimately wrecking it. A speaker demands power amp level. At the same time, since the present/voltage is so low, your speaker would end up being extreme calm. There are usually speakers that have got a very high effectiveness, but they put on't arrive cheap and would still require a bit even more than a collection out/cell phone out there can deliver.

Here is usually a forum for higher efficiency audio speakers: I acquired a terratec soundcard decades ago that could be jumpered to a higher result, it was useable, but todays computers only have line out/cell phone out. What you can perform is certainly this: obtain yourself some inexpensive computer audio speakers with builtin energy amp, the cheap ones proceed for 10 pounds or less here. Open them, reduce the cables to the builtin loudspeakers wich are usually rubbish, and solder your very own speakers on it. If you possess a set that has a 12 volt power source you could crack it into your personal computer and use your computer systems power offer.

I bought a collection of loudspeakers for my pc, (logitech z .200) and an audio interface for my microphone. The audio speakers are usually wired jointly and I has been wondering if it had been achievable to reduce the cables linking the speakers and put RCA plugs on them tó connect them intó the back of my audio user interface. The left speaker only offers the cable connecting it to the correct speaker, and the right speaker provides the connecting wire, strength, and a 3.5mmeters for connecting it to the pc.Can be this in any method possible? And if therefore, what specifically would I require to do?Thanks a lot. I bought a set of audio speakers for my pc, (logitech z200) and an audio interface for my microphone.

The speakers are wired collectively and I was wondering if it had been feasible to reduce the wires linking the loudspeakers and put RCA attaches on them tó connect them intó the back again of my audio user interface. The remaining speaker only has the wire hooking up it to the right speaker, and the right speaker has the connecting wire, power, and a 3.5mmichael for linking it to the pc.Will be this in any way achievable?

And if therefore, what specifically would I need to perform?ThanksNot actually. The remaining speaker wants to get power from the right speaker.As above, just obtain a 3.5mm-RCA adapter.